Actions

Modelling Pulleys

From DT Online

The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
PulleyBox.png


Description

Pulleys a provide a basic method of transferring motion from a motor to a model.

The Pulleys can be made using discs of card and MDF or from 'found objects' such as plastics lids, cotton reels - or even large beads.


Note: If plastics lids or cotton reels are used, card or MDF discs may have to be glued to them using Double-Sided Tape, an Adhesive such as epoxy resin or a Glue Gun since PVA will be ineffective.


Elastic bands provide suitable Drive Belts : for most purposes, use narrow ones and double them up or use several of them if a stronger belt is needed. Wide drive belts will tend to 'climb' out of the Pulley.


Making Model Pulleys
Card and MDF Discs Medium thickness card discs can be glued to each side of an MDF or Ply disc, approximately 10mm smaller in diameter, to make a grooved pulley.

In most cases PVA is a suitable glue to use (i.e. unless the card is laminated or plastics-coated in some way).

CardMDFPulley.png
Screwtop Jar Lids Typically found as coffee jar lids, these have a deep enough rim not to need any sides to stop the drive belt coming off.


A small MDF or Ply disc glued in the centre will provide a better location for the axle than the thin plastics of the lid (see note about gluing plastics above).


Note: The lids are usually manufactured by a process known as Injection Moulding and the centre can be found by looking for the small 'pip' left over from where the molten plastics was squeezed in to the mould.


ScrewTopLidPulleys.png
Cotton Reels The hole down the centre of cotton reeels will most likely be too big to be a tight fit on Stripwood axles and so they too may need a small MDF or Ply disc gluing on to them (most will be made of plastics so see note about gluing plastics above).


The loose fit of a cotton reel can also be an advantage. If a larger pulley is glued to the side of a cotton reel (and also drilled out to be a loose fit) then the larger pulley will rotate at the same speed as the cotton reel and this is put to use to make speed reducing pulley arrangements - see below

CottonReelLayshaftPulley.png
Wooden Beads The rounded surface of a large wooden bead can simulate the barrel-shaped pulleys once used when a single Lineshaft transferred the power from a central engine to all the machines on a factory floor.


If wide elastic bands are chosen as drive belts, these may be the only type of pulley they don't attempt to 'climb' out of.

BeadPulley.png


Driver and Driven
Same Size Pulleys If two pulleys of the same diameter are fixed to two parallel shafts then the two shafts will both rotate at the same speed and in the same direction.


The pulley supplying the power (e.g. the one connected to the motor) is known as the Driver and the one the motion is being transferred to is known as the Driven.

ParallelShaftPulleys.png
Different Size Pulleys If the two pulleys are different sizes then a smaller Driver pulley will cause a larger Driven pulley to rotate more slowly and a larger Driver pulley will cause a smaller Driven pulley to rotate more quickly.


Engineers refer to these speed changes as the Velocity Ratio which means, for example, that a 50mm diameter Driver pulley would cause a 100mm Driven pulley (i.e. twice the diameter) to rotate at half the speed.


Activity: What would happen to the speed of a 50mm Driven pulley if the Driver pulley was 100mm diameter?


DrivePulleys.png


Changing Speed
Cone Pulley Several grooved pulleys of different diameters can be glued together in a stack as shown. Two such arrangements fixed to parallel shafts, with one upside down to the other, create a Cone Pulley drive as used in many Machine Tools.


A single drive belt can be moved between different pairs of pulleys to either speed up or slow down the Driven pulley.

ConePulleys.png
Double Reduction An extra axle, known as a Layshaft can be inserted between the Driver pulley and the Driven. A loose fitting double pulley (e.g. made from a cotton reel glued to a larger grooved pulley) is allowed to rotate freely on the Layshaft.


As the motor drive is transferred to the large grooved pulley, the cotton reel is caused to rotate at the same reduced speed. If the cotton reel is then itself connected to a larger final drive pulley, then a second speed reduction occurs.

DoubleReductionPulleys.png
Multiple Reductions The idea of using a loose fitting double pulley to enable a second speed reduction can be repeated - several times if necessary. The drive from the motor is then repeatedly transferred from small pulley to large pulley until it reaches the final Driven output pulley.


To avoid adding extra Layshafts, the final drive shaft can be used by allowing the double pulleys to run loosely over it and only fixing the final Driven pulley to the axle.


Note: Although Gears are used instead of Pulleys, the use of a Layshaft in this way is the idea around which car gearboxes are designed.


LayshaftPulleys.png


Changing Direction
Reverse Rotation If the drive belt is given a half twist then the Driven pulley will rotate in the opposite direction to the Driver pulley
ReversingPulleys.png
Changing Drive Alignment The Driver and Driven driveshafts do not always have to be parallel to each other. Pulleys and drive belts are flexible enough to enable the two axles to be at right angles to each other for example.
RightAngleDrivePulleys.png


DT Online Buyers' Guide

Notes:

  • MDF Discs which are pre-drilled are most useful if available, otherwise this might be done as preparation before using with younger children - alternatively a Hand Drill Stand could be used (if neccessary, adults or older children can cut them out of strips of MDF or Ply using a Holesaw).
  • Dowels 4mm, 5mm, and 6mm are useful sizes for axles.
  • Florist Wire is easily bent into shape whereas stiff wire, such as Brass Brazing Rod, is more suitable for connecting rods.


MDF and Ply Discs Wood Dowel Rod Wooden Clothes Pegs Wooden Matchsticks for Craft Wooden Lolly Sticks for Craft Wooden Cocktail Sticks and Skewers for Craft Unpainted Wooden Beads Polystyrene Balls Florists Wire Brazing Rod
MDF and ply discs Wood Dowel Rod Wooden Clothes Pegs Wooden Matchsticks for Craft Wooden Lolly Sticks for Craft Wooden Cocktail Sticks and Skewers for Craft Unpainted Wooden Beads Polystyrene Balls Florists Wire Brazing Rod
Cotton Reels Wooden Spools Copper Foil Tape PVC Tube Assorted Cable Ties Hook and Loop Stick On Tape Coloured Card for Craft Greyboard Cotton String Elastic Bands
Cotton Reels Wooden Spools Copper Foil Tape PVC Tube Assorted Cable Ties Hook and Loop Stick On Tape Coloured Card for Craft Greyboard Cotton String Elastic Bands