View source for Nails and Pins

[[File:DovetailNailingPunching.png |200px|right]]

The holding power of [https://en.wikipedia.org/wiki/Nail_%28fastener%29 '''Nails''']  depends upon [https://en.wikipedia.org/wiki/Friction '''Friction'''] and some nails have coatings or grips designed into the body of the nail ''(i.e. shank)''  to improve this. In addition, some coatings are applied to improve resistance to corrosion  ''(e.g. [https://en.wikipedia.org/wiki/Galvanization '''Galvanising''']).'' Nails may be driven in at opposing angles as shown. This is a process known as '''Dovetail Nailing''' and improves their holding power.


Also shown opposite is the use of a '''[[Punches|Nail Punch]]'''. It is good practice on fine work to drive nails in to a few millimeters of the surface then punch them below it. The punched hole can then be filled with [https://en.wikipedia.org/wiki/Wood_putty '''Wood Filler'''].


When using nails in softwoods they can usually be driven in directly but for hardwoods, and sometimes to avoid splitting near the end on any timbers, a small hole may be drilled in the top piece first - or bored with a '''[[Drills and Drilling|Bradawl]]'''.


Most [https://en.wikipedia.org/wiki/Nail_%28fastener%29 '''Nails'''] are made from [https://en.wikipedia.org/wiki/Drawing_%28manufacturing%29 ''cold drawn''] [https://en.wikipedia.org/wiki/Carbon_steel#Mild_and_low-carbon_steel ''mild steel''] wire. This process improves the strength or wire by [https://en.wikipedia.org/wiki/Work_hardening ''work hardening''] such that '''Nails''' can be driven into timber by use of '''[[Hammers]]'''. If nails do become bent they can easily be withdrawn using '''[[Pincers and Crow Bars|Pincers]]''' or a '''[[Hammers|Claw Hammer]]''' for example.
----
<span style="color: green">'''Note:'''
Nails often bend whilst being driven in because the hammer head is not kept clean and polished by regular rubbing it on a piece of fine '''[[Glasspaper]]'''. 
</span>
----
<span style="color: red">'''Safety Point!'''
Builders may also use [https://en.wikipedia.org/wiki/Nail_gun '''Nail Guns'''] but these are extremely dangerous and not suitable for school use.
</span>
----
{|
|-
| '''Round Wire Nails'''
| Used for general carpentry where the presence of the round steel head would be acceptable ''(e.g. packing case construction and soft timber framing)'' 
| [[File:RndWireNail.png|100px|right]]
|-
| '''Oval Wire Nails'''
| These enter the wood cleanly with less tendency to cause splitting and are used as finishing nails for most joinery work.
----
<span style="color: green">'''Note:'''
When driving in a number of nails close together, avoid positioning them in line with the [https://en.wikipedia.org/wiki/Wood_grain grain] but stagger them to help avoid splitting. 
</span>
---- 
| [[File:OvalWireNails.png|100px|right]]
|-
| '''Panel Pins'''
| Use for fine cabinet work, these are thin nails with an inverted cone-shaped head which enters the wood cleanly. ''(Shown in the background is a '''Push Pin Tool''' which can be used to hold small panel pins magnetically and then push them into the material. instead of using a hammer)''
| [[File:PanelPins.png|100px|right]]
|-
| '''Deep Drive Panel Pins'''
| Panel Pins which have a double cone-shaped head resulting in a pointed top such that the last blow drives them below the surface.
| [[File:DeepDrivePanelPins.png|100px|right]]
|-
| '''Ring Nails'''
| these have ridges around the shank to provide extra grip.
| [[File:RingNails.png|100px|right]]
|-
| '''Corrugated Fasteners''' ''(aka Wiggle Nail)''
| used to strengthen edge to edge joints ''(e.g. as in the sides of packing cases)'' or holding together the framed core of cheap ply-skinned panels.
| [[File:CorrugatedFasteners.png|100px|right]]
|-
|  '''Tacks'''
| used to secure thin materials and fabrics to wood ''(e.g. carpets to floorboards)''.
| [[File:Tacks.png|100px|right]]
|-
| '''Upholstery Tacks'''
| usually made with a large dome-shaped [https://en.wikipedia.org/wiki/Brass brass] or [https://en.wikipedia.org/wiki/Japanning black-japanned] head to form a decorative feature in some forms of upholstery work. 
| [[File:UpholsteryTacks.png|100px|right]]
|-
| '''Clout Nails'''
| usually [https://en.wikipedia.org/wiki/Galvanization galvanised] and with a large round head, these are used mainly for holding down roofing felt.
| [[File:CloutNail.png|100px|right]]
|-
| '''Floor Brad'''
| rectangular in cross section and stamped from flat sheet, these are used mainly for fixing floorboards to [https://en.wikipedia.org/wiki/Joist joists.]
| [[File:FloorBrad.png|100px|right]]
|-
| '''Fencing Staples'''
| a small U-shaped nail, often [https://en.wikipedia.org/wiki/Galvanization galvanised] and commonly used for fixing fence wire to posts.
| [[File:FenceStaples.png|100px|right]]
|-
| '''Masonry Nails'''
| a hardened stout nail designed to be driven directly into concrete.
| [[File:MasonryNail.png|100px|right]]
|}




[[Category:Fixings and Fastenings]]