View source for Mortise and Tenon Joint

[https://en.wikipedia.org/wiki/Mortise_and_tenon '''Mortise and Tenon Joints'''] ''(aka Mortice and Tenon)'' are the most common and strongest framing joint. They can be used wherever a frame construction is required and have many variations.


The illustrations show the most conventional types but actual proportions and configurations of '''Mortise and Tenon Joints''' can be varied to suit the tasks in hand ''(e.g. joining at angles other than a right-angle or joining a rail on to a turned leg)''.  They are commonly cut as '''Through Mortise and Tenons''' in which the '''Mortise''' passes completely through the material. '''Mortise and Tenon Joints''' may also be combined with '''[[Dowel Joint|Dowels]]''' or '''[[Housing Joint|Housings]]''' to add strength to those joints.


The two main parts of the joint are:
* the '''Tenon''', which is cut on the end of one joining piece ''(generally called the 'rail')''
* the '''Mortise''', which is a recess, slot or socket cut into the edge of the second piece ''(generally called the 'stile')''.


Where '''Mortise and Tenon Joints''' are used to create a frame corner ''(i.e. at the end of a 'stile')'' the '''Mortise''' is stopped short of the end and a '''Haunched Mortise and Tenon''' used. In high quality cabinet work, the '''Mortises''' may be stopped short of the width of the stile such that [https://en.wikipedia.org/wiki/Wood_grain '''End Grain'''] remains hidden. These are known as '''Stub Mortise and Tenons'''.


[[File:MortiseTenon.png|400px|right]]  
For extra strength, saw cuts are made down the '''Tenons''' which receive wedges when assembled. When wedges are used in a 'stopped' '''Mortise and Tenon Joint''', it is known as '''Fox Wedging'''. 


__TOC__


<div style="clear: both;"></div>
=====Marking Out=====
* The joining pieces are prepared as normal and marked with '''[[Face Side and Face Edge]]''' marks.
* The joint positions are marked out using a Pencil and '''[[Try Square]]'''.
* The pins of a '''[[Gauges|Mortise Gauge]]''' are set to the width of a '''[[Chisels|Mortise Chisel]]''', chosen to be about one third the thickness of timber, and the '''[[Gauges|Gauge Stock]]''' adjusted to scribe the double lines down the centre of the timber thickness.
* If required, a '''[[Gauges|Marking Gauge]]''' is used to scribe the depth of any '''Haunches'''
* A '''[[Marking Knife]]''' is used with a '''[[Try Square]]''' to scribe an incised line along where the shoulders are to be cut.
[[File:MortiseTenonMarkingOut.png|500px|right]]


<div style="clear: both;"></div>
=====Sawing the Shoulders=====
[[File:MortiseTenonSawingShoulders.png|400px|right]]
* '''[[Paring|Pare]]''' with a '''[[Chisels|Chisel]]''' to cut a shallow 'Vee' groove across the line of the shoulders to guide the saw.
* If needed, on wider boards for example, a piece of scrap timber can be clamped along the line to be cut to guide the saw ''(see '''[[Corner Lap Joint]]''')''.
* Saw all shoulders down to the gauge lines using a '''[[Tenon Saw]]'''.
----
<span style="color: green">'''Note:'''
Turn the work piece round in the vice to ensure it is the waste which is always on the 'blind side' of the saw.
</span>
----

=====Sawing the Tenons=====
* The sides ''(or cheeks)'' of the '''Tenons''' are cut with a '''[[Tenon Saw]]'''.
* Arrange the work-piece in the '''[[Carpenters Vice]]''' at an angle with the waste on the ''blind side'' of the saw.
* Using a '''[[Tenon Saw]]''' carefully saw along the gauge lines along the side and across the end.
* Reverse the angle and saw position carefully to saw along the gauge lines along the other side and once again across the end.
* Arrange the work vertically in the '''[[Carpenters Vice]]''' and continue the cut down to the ''shoulders'', using the previous angled cuts to guide the blade - and always with the waste on the ''blind side'' of the saw.
[[File:HalvingJointSawingCheek.png|700px|right]]
----
<span style="color: green">'''Note:'''
The sides ''(or cheeks)'' of '''Tenons''' can also be cut down to the ''shoulders'' using a '''[[Bandsaw]]'''.
</span>
----
* If required, the sawn '''Tenons''' can be '''[[Paring|Pared]]''' to the gauge lines with a sharp '''[[Chisels|Chisel]]''' ''(but a good crafts-person will produce joints 'off the saw'!)''  
[[File:TenonParing.png|200px|left]]
[[File:TenonSawingHaunch.png |300px|right]]


* For a '''Haunched Mortise and Tenon Joint''', the '''Haunches are cut using a '''[[Tenon Saw]]'''.

<div style="clear: both;"></div>
=====Cutting Mortises=====
There are several ways to cut the '''Mortises''':
[[File:CuttingMortise.png|300px|right]]
* '''Using a [[Chisels|Mortise Chisel]]'''
** Grip the work firmly in a '''[[Carpenters Vice]]''' and set it deep in to the jaws to add side support as the joint is cut ''(if needed, scap wood could also be placed under the work-piece to add support under)''.
** Position the '''[[Chisels|Mortise Chisel]]''' a few millimetres in from the centre of the '''Mortise''' and work each way towards the end the blade bevel is facing  ''(this is so that when struck with a '''[[Mallets|Mallet]]''', the '''[[Chisels|Chisel]]''' will be driven not only downwards but also towards the centre of the '''Mortise''')''.
** Once the bulk of the waste is cleared out, reverse the '''[[Chisels|Mortise Chisel]]''' such that its blade bevel is facing the centre of the '''Mortise''' and finished to size with vertical cuts.
* '''Drilling and [[Paring]]'''
** Drill holes close together along the length of the '''Mortise''' - use a drill diameter slightly less than the finished width ''(to allow for cleaning up by '''[[Paring]]''' after)''.
** Clear out the waste using '''[[Chisels]]''' ''(see '''[[Bridle_Joint#Cutting_Bridle_Joint_.27Sockets.27|Bridle Joint]]''')''.
* '''Hollow Chisel [[Mortiser]]'''
** Cut along the length of the '''Mortise''' with repeated cuts from a '''[[Mortiser|Hollow Chisel Mortiser]]'''  to remove all waste ''(see '''[[Bridle_Joint#Cutting_Bridle_Joint_.27Sockets.27|Bridle Joint]]''')''.


<div style="clear: both;"></div>
=====Using a Router=====
[[File:MortiseTenonRouterUse.png |300px|right]]
With the work-piece securely held, a '''[[Router]]''' can be used to cut '''Tenons''' from the beginning. If required, additional pieces of equal thickness timber can be used to balance it and guides, '''[[Jig|Jigs]]''' or fences set up to obviate the need for some marking out.


It is possible also to clamp several work-pieces together to cut multiple '''Tenons''' in a single cut ''(but take care to ensure the depth of the 'shoulder' and the thickness of the 'cheek' is always gauged from the '''[[Face Side and Face Edge|Face Side]]''')'' 


----
<span style="color: red">'''Safety Point!'''
All high-speed woodcutting machinery is dangerous. '''[[Router|Routers]]''' and '''[[Bandsaw|Bandsaws]]''' must only be used by trained adults or trainees under direct supervision by specifically trained staff.
</span>
----
<div style="clear: both;"></div>
=====Types of Mortise and Tenon Joint=====
[[File:SlopingShoulderHaunched.png|200px|right]]
* '''Haunched Mortise and Tenon'''
** These are used where the rail meets a stile or leg near the end.
** The '''Mortise''' is cut a litle narrower than the width of the rail except for a portion which receives the base of the '''Tenon''' and forms the '''Haunch'''.
** The purpose of the '''Haunch''' is to maintain support across the full width of the '''Tenon''' to help prevent any twisting.
** A '''Haunched Mortise and Tenon''' also has the advantage that it can usefully close off a [https://en.wikipedia.org/wiki/Groove_%28joinery%29 '''Groove'''] where these run round the inside edge of a frame.
** Where it is undesirable to show the '''Haunch''' at the end, the '''Tenon''' shoulder can be sloped and this also can close off a [ https://en.wikipedia.org/wiki/Groove_%28joinery%29 '''Groove'''].
** '''Tenons''' with such sloping shoulders are also known as '''Gunstock Mortise and Tenons'''.


<div style="clear: both;"></div>
[[File:BarefacedLongShort.png|150px|right]]
* '''Barefaced and Long and Short Shouldered Mortise and Tenon'''
** Used in situations where it is a [https://en.wikipedia.org/wiki/Rabbet '''Rebate'''] ''(aka Rabbet)'' running round the inside of a frame.
** A '''Barefaced Tenon''' enables a single panel to be fitted to a frame where cross rails or end rails would normally prevent this.
** To close off the end of a [https://en.wikipedia.org/wiki/Rabbet '''Rebate'''], one shoulder of the '''Tenon''' can be made to extend in to it to create a '''Long and Short Shoulder Mortise and Tenon'''.
<div style="clear: both;"></div>


[[File:RailTenons.png|200px|right]]
* '''Tenoned Rails'''
** '''Mortises''' may be cut through the face of a stile as well as the edge and may also be '''Haunched''' if near the end.
** This orientation can be useful where table cross-rails meet end frames for example.
<div style="clear: both;"></div>


[[File:TwinStub.png|200px|right]]
* '''Double and Twin Tenons'''
** '''Double Tenons''' are useful where the rail is very wide since an over-wide '''Mortise''' may weaken the stile and such a wide '''Tenon''' may become loose because of shrinkage.
** The two '''Tenons''' can be connected by a '''Haunch''' type connecting piece to help prevent the rail twisting.
** '''Twin Tenons''' are used on thick timber and are also a useful joint to connect wide rails to end frames as shown.
** '''Twin Tenons''' can be used on the end of a shelf for example, perhaps which is also '''[[Housing Joint|Housed]]''' into the carcass sides, and if '''Through Tenons''', can be used with contrasting wedges to create a decorative effect on the outside of the cabinet. 


<div style="clear: both;"></div>
[[File:TuskTenon.png|200px|right]]
* '''Tusk Tenon'''
** '''Through Tenons''' can be extended beyond the thickness of the stile and shaped for decoration.
** They may also have pegs or wedges inserted to pull them tighter into the ''Mortise''' - these are known as '''Tusk Tenons'''.  
<div style="clear: both;"></div>


[[File:WedgedTenon.png|200px|right]]
* '''Wedging Tenons'''
** Saw cuts can be made down the '''Tenons''' to receive wedges on assembly.
** '''Through Tenons''' may have wedges of a contrasting timber and used to add some decoration.
** Care must be taken to ensure the wedges are positioned across the '''Tenon''', or on a diagonal, to avoid any sideways forces acting on the '''Mortise''' when they are driven in.
** '''Stub Tenons''' may also be wedged. The wedges are positioned into the saw cuts before the '''Tenon''' is driven into the stopped ''(or blind)'' '''Mortise'''.
** This is known as '''Fox Wedging''' and care must be taken to ensure the wedges are accurately cut to ensure the  joint closes completely on assembly.  



[[Category:Wood Joints]]