View source for Keys, Keyways and Splines

[[File:Keyseating.jpg|right|275px|Keyseating|link=https://commons.wikimedia.org/wiki/File:Keyseating.jpg]]
__TOC__


=====Description=====

Components including '''[[:Category:Gears|Gears]]''', '''[[:Category:Pulleys|Pulleys]]''' or '''[[:Category:Cams|Cams]]''' often need to be fixed to a drive shaft or axle such that they rotate with the shaft.

This can be achieved by making the hole a very tight fit on the shaft ''(known to [https://en.wikipedia.org/wiki/Engineer '''Engineers'''] and [https://en.wikipedia.org/wiki/Mechanic '''Mechanics'''] as a [https://en.wikipedia.org/wiki/Interference_fit '''Press Fit'''] or [https://en.wikipedia.org/wiki/Interference_fit '''Interference Fit'''])'' but this is not suitable if the component has to be removable.
----
<span style="color: green">'''Note:'''
When making simple working models in wood, drilling a tight size hole, or even gluing, is usually sufficient  
</span>
----
[https://en.wikipedia.org/wiki/Set_screw '''Grub Screws'''] can be used where the loading is not high but otherwise [https://en.wikipedia.org/wiki/Key_%28engineering%29 '''Keys'''] are preferred.
----
<span style="color: green">'''Note:'''
When using [https://en.wikipedia.org/wiki/Set_screw '''Grub Screws'''] a better grip can be achieved if two are used but these must be positioned at 90° to each other. Alternatively, the screw can be tightened on to a ''''flat'''' which has been '''[[Files and Rasps|filed]]''' or '''[[Milling Machine|milled]]''' on to the shaft.
</span>
----
In some circumstances, the component has to not only rotate with the shaft but also slide along it as it rotates ''(e.g. in [https://en.wikipedia.org/wiki/Transmission_%28mechanics%29 '''Gear Boxes'''])''. In these situations a [https://en.wikipedia.org/wiki/Spline_%28mechanical%29 '''Spline Shaft'''] could be used.


=====Features and Applications=====
{|
|-
| [https://en.wikipedia.org/wiki/Set_screw '''Use of Grub Screws on a Plain Shaft''']
| This is a relatively straightforward means of attaching components to shafts suitable for light to moderate loading. It requires no special tooling needing only holes to be drilled and tapped into the body of the component. <span style="color: green">''('''Note:''' the two Grub Screws are positioned at 90° to each other such that the shaft is pressed against the inside surface of the bore rather than being held only between the two screw ends, as would be the case if they were opposite each other).''</span>
| [[File:ScrewedCollarPlainShaft.png|150px|right]]
|-
| [https://en.wikipedia.org/wiki/Set_screw '''Grub Screw mated on to a ''‘Flat’''''']
| Screws located on to a '''‘flat’''' can increase the resistance to slippage and help align components along a shaft.
| [[File:GrubScrewFlat.png |150px|right]]
|-
| '''Use of a Squared Shaft'''
| Suitable only where a component is fitted at the end of a shaft but capable of transmitting very high loads and provides a positive location of the component in one of four positions.
| [[File:SquareShaft.png|200px|right]]
|-
| [https://en.wikipedia.org/wiki/Key_%28engineering%29#Parallel_keys '''Feather Key''' ''(aka Flat Key)'']
| These can be used at any point along the shaft to provide a very positive location and capable of transmitting high loads ''(may need spacers or the presence of other components to prevent movement along the axis of the shaft)''. The '''Keyway''' can be cut using a '''[[Milling Machine|End Mill]]'''.
| [[File:FeatherKeyAssy.png|200px|right]]
|-
| [https://en.wikipedia.org/wiki/Key_%28engineering%29#Woodruff_key '''Woodruff Key''']
| In common use on tapered shafts because they can tilt to accommodate the taper angle. The '''Keyway''' is cut using a '''Woodruff Cutter''' in a '''[[Milling Machine]]'''.
| [[File:WoodruffKeyAssy.png|200px|right]]
|-
| [https://en.wikipedia.org/wiki/Key_%28engineering%29#Tapered_keys '''Gib Head Key''']
| Useful when the components fitted at the end of a shaft may need to be removed easily - the key is removed by striking a wedge-shaped '''[[:Category:Punches|drift]]''' between the head and the component. The '''Keyway''' can be cut using a '''[[Milling Machine]]''' with a '''Side and Face Cutter''' or a '''Slitting Saw'''.
| [[File:GibHeadKeyAssy.png|200px|right]]
|-
| '''Use of Drilled Holes and Pegs'''
| A relatively simple way of providing a ''key-type'' location is to drill axially down the joint between component and shaft then inserting small rods as shown. 
| [[File:DrilledKeyAssy.png|200px|right]]
|-
| [https://en.wikipedia.org/wiki/Spline_%28mechanical%29 '''Splined Shaft''']
| In common use in car gearboxes and also the main transmission shaft which has to be telescopic to allow for the movement of car supension.  
| [[File:Splines.png|200px|right]]
|}

{{Keyways Buyers Guide}}

[[Category:Fixings and Fastenings]]