Gear Train - Revision history

DT Online: Added Template

2016-08-04T17:11:41Z

Added Template

← Older revision		Revision as of 17:11, 4 August 2016
Line 1:		Line 1:
	[[File:g3.gif\|300px\|right]]		[[File:g3.gif\|300px\|right]]
			__TOC__


			=====Description=====

	If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.		If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.


			=====Features and Applications=====

	The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear, but both loosely rotating, on an intermediate [https://en.wikipedia.org/wiki/Layshafthttp://www.example.com '''‘Layshaft’'''] and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional ‘layshafts’ can be used and the process repeated again. The use of ‘layshafts’ is common in car gearboxes for example.		The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear, but both loosely rotating, on an intermediate [https://en.wikipedia.org/wiki/Layshafthttp://www.example.com '''‘Layshaft’'''] and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional ‘layshafts’ can be used and the process repeated again. The use of ‘layshafts’ is common in car gearboxes for example.
Line 15:		Line 20:
	----		----

			{{Gears Buyers Guide}}

DT Online at 08:45, 19 April 2016

2016-04-19T08:45:27Z

← Older revision		Revision as of 08:45, 19 April 2016
Line 1:		Line 1:
	[[File:g3.gif\|~~200px~~\|right]]		[[File:g3.gif\|300px\|right]]


	If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.		If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.


	The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear, but both loosely rotating, on an intermediate [https://en.wikipedia.org/wiki/Layshafthttp://www.example.com '''‘Layshaft’'''] and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional ‘layshafts’ can be used and the process repeated again. The use of ‘layshafts’ is common in car gearboxes for example.		The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear, but both loosely rotating, on an intermediate [https://en.wikipedia.org/wiki/Layshafthttp://www.example.com '''‘Layshaft’'''] and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional ‘layshafts’ can be used and the process repeated again. The use of ‘layshafts’ is common in car gearboxes for example.


	To calculate the total ‘gearing down’ ''(or ‘gearing up’ if the roles of large and small gears are reversed)'', the ‘gear ratio’ for each meshing pair of gears is calculated and the result from each pair in the ‘gear train’ multiplied together. For example, a 20mm dia driver gear meshes with a 60mm dia gear which is connected to a 20mm gear on a layshaft and this in turn meshes with a 60mm dia gear on the output shaft. Each meshing pair has a gear ratio of 3:1 so the overall gear ratio is 9:1.		To calculate the total ‘gearing down’ ''(or ‘gearing up’ if the roles of large and small gears are reversed)'', the ‘gear ratio’ for each meshing pair of gears is calculated and the result from each pair in the ‘gear train’ multiplied together. For example, a 20mm dia driver gear meshes with a 60mm dia gear which is connected to a 20mm gear on a layshaft and this in turn meshes with a 60mm dia gear on the output shaft. Each meshing pair has a gear ratio of 3:1 so the overall gear ratio is 9:1.

DT Online: Changed image

2016-04-19T08:39:44Z

Changed image

← Older revision		Revision as of 08:39, 19 April 2016
Line 1:		Line 1:
	[[File:~~GearTrain~~.~~jpg~~ \|200px\|right]]		[[File:g3.gif\|200px\|right]]

	If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.		If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.

DT Online at 18:30, 15 February 2015

2015-02-15T18:30:10Z

← Older revision		Revision as of 18:30, 15 February 2015
Line 18:		Line 18:

	[[Category:Secondary]]		[[Category:Secondary]]
	~~[[Category:Mechanisms]]~~
	[[Category:Gears]]		[[Category:Gears]]

DT Online: Added Layshaft link

2015-02-11T16:56:40Z

Added Layshaft link

← Older revision		Revision as of 16:56, 11 February 2015
Line 3:		Line 3:
	If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.		If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.

	The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear but both loosely rotating on an intermediate '''‘Layshaft’''' and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional ~~layshafts~~ can be used and the process repeated again. The use of ~~layshafts~~ is common in car gearboxes for example.		The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear, but both loosely rotating, on an intermediate [https://en.wikipedia.org/wiki/Layshafthttp://www.example.com '''‘Layshaft’'''] and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional ‘layshafts’ can be used and the process repeated again. The use of ‘layshafts’ is common in car gearboxes for example.

	To calculate the total ‘gearing down’ ''(or ‘gearing up’ if the roles of large and small gears are reversed)'', the ‘gear ratio’ for each meshing pair of gears is calculated and the result from each pair in the ‘gear train’ multiplied together. For example, a 20mm dia driver gear meshes with a 60mm dia gear which is connected to a 20mm gear on a layshaft and this in turn meshes with a 60mm dia gear on the output shaft. Each meshing pair has a gear ratio of 3:1 so the overall gear ratio is 9:1.		To calculate the total ‘gearing down’ ''(or ‘gearing up’ if the roles of large and small gears are reversed)'', the ‘gear ratio’ for each meshing pair of gears is calculated and the result from each pair in the ‘gear train’ multiplied together. For example, a 20mm dia driver gear meshes with a 60mm dia gear which is connected to a 20mm gear on a layshaft and this in turn meshes with a 60mm dia gear on the output shaft. Each meshing pair has a gear ratio of 3:1 so the overall gear ratio is 9:1.

DT Online: Created Gear Train

2015-02-11T16:51:39Z

Created Gear Train

New page

[[File:GearTrain.jpg |200px|right]]

If a small '''driver''' gear meshes with the larger of two gears joined together on a common shaft then the smaller gear on that shaft will also rotate at the slower speed. The smaller gear can then be used to drive a large gear on a second shaft to cause a second gear reduction. This arrangement is known as a [https://en.wikipedia.org/wiki/Gear_train '''Gear Train'''] and is a good way of ‘gearing down’ a rapidly revolving electric drive motor for example.

The process can be repeated by engaging the smaller gear on the drive shaft with a large gear fixed to a small gear but both loosely rotating on an intermediate '''‘Layshaft’''' and this second small gear used to drive a large gear on the final output shaft. If even greater speed reductions are required, additional layshafts can be used and the process repeated again. The use of layshafts is common in car gearboxes for example.

To calculate the total ‘gearing down’ ''(or ‘gearing up’ if the roles of large and small gears are reversed)'', the ‘gear ratio’ for each meshing pair of gears is calculated and the result from each pair in the ‘gear train’ multiplied together. For example, a 20mm dia driver gear meshes with a 60mm dia gear which is connected to a 20mm gear on a layshaft and this in turn meshes with a 60mm dia gear on the output shaft. Each meshing pair has a gear ratio of 3:1 so the overall gear ratio is 9:1.

----
<span style="color: green">'''Note:'''If two meshing gears have the same number of teeth, they will rotate at the same speed, however if they have different numbers of teeth then the gear with fewer teeth will rotate more quickly - i.e. the '''[[Velocity Ratio]]''' ''(or [https://en.wikipedia.org/wiki/Gear_ratio ‘Gear Ratio’])'' of a pair of meshing gears is given as the ''Number of Teeth of the Driver Gear divided by the Number of Teeth'' of the Driven Gear. The '''[[Mechanical Advantage]]''' ''(or [https://en.wikipedia.org/wiki/Torque ‘Torque Ratio’])'' similarly is given as ''No. of Teeth on Driven divided by No. of Teeth on Driver''.
</span>
----

[[Category:Secondary]]
[[Category:Mechanisms]]
[[Category:Gears]]