DT Online: Added Template

2016-07-05T14:01:37Z

Added Template

← Older revision		Revision as of 14:01, 5 July 2016
Line 60:		Line 60:
	Finally, shading or '''''rendering''''' will complete the drawing.		Finally, shading or '''''rendering''''' will complete the drawing.


			<div style="clear: both;"></div>


			{{Graphics Buyers Guide}}

	[[Category:Perspective]]		[[Category:Perspective]]

DT Online: Added Category

2015-12-30T19:33:40Z

Added Category

← Older revision		Revision as of 19:33, 30 December 2015
Line 61:		Line 61:


	~~=====Animation=====~~		[[Category:Perspective]]
	~~''(Click to activate)''~~
	~~<div style="clear: both;"></div>~~
	~~::::::::::~~[[~~File~~:~~SlopeAnimation.gif\|500px\|~~]]

DT Online: Added link

2015-12-30T19:23:45Z

Added link

← Older revision		Revision as of 19:23, 30 December 2015
Line 62:		Line 62:

	=====Animation=====		=====Animation=====
			''(Click to activate)''
	<div style="clear: both;"></div>		<div style="clear: both;"></div>
	::::::::::[[File:SlopeAnimation.gif\|500px\|]]		::::::::::[[File:SlopeAnimation.gif\|500px\|]]

DT Online: Created article

2015-12-30T19:21:58Z

Created article

New page

In most drawing projections, it is possible to draw only vertical and horizontal lines directly. Any sloping surface have to be drawn by joining together two end points which have been constructed by intersecting a vertical and horizontal line
[[File:Slopingroofs.png|400px|right]]

__TOC__

<div style="clear: both;"></div>
=====Construction=====
Look carefully at the red lines - these are drawn in perspective as if the house was completely cuboid. One way of thinking about it is to imagine that what you are drawing is packed inside a close fitting box and you draw the boxes first.

::::::::::[[File:Slopingroof2.png|400px|right]]

Once these 'boxes' or 'crates' have been drawn it is possible, using additional lines, to identify points on their edges which define the ends of the roof slope.
----
<span style="color: green">'''Note:'''
The technique of drawing complex objects in 3D by first imagining they are packed inside tight-fitting boxes or crates is sometimes called ''''crating''''.
</span>
----
=====Step by Step Construction=====

[[File:ObliquePerspective2.gif|400px|right]]
'''Step 1'''

The first task is to draw the imaginary close-fitting 'box' or 'crate' that would contain the object you wish to draw.. Using '''Single Point Perspective''' this is done simply by starting with a square or rectangle then projecting back to a suitable '''Central Vanishing Point ''(CVP)'''''.

<div style="clear: both;"></div>
[[File:ObliquePerspective3.gif|400px|right]]
'''Step 2'''

Next draw another square or rectangle within the projection lines.
----
<span style="color: green">'''Note:'''
The second square or rectangle will be a '''Similar Figure''' to the first and, in '''Single Point Perspective''' sides of the figures remain vertical or horizontal.
</span>
----
[[File:ObliquePerspective6.gif|400px|right]]
'''Step 3'''

Any slopes or angles required can now be drawn directly on the end face of the object and projected back to the CVP to locate points on the rear face.

<div style="clear: both;"></div>
[[File:ObliquePerspective7.gif|400px|right]]
'''Step 4'''

Next 'line in' the required outline of the object.
----
<span style="color: green">'''Note:'''
'''Oblique''' projections such as '''Single Point Perspective''', are particularly useful when drawing objects that have a complex cross section but are relatively plain other respects - such as extruded or moulded sections.
</span>
----
<div style="clear: both;"></div>
[[File:ObliquePerspective8.gif|400px|right]]
'''Step 5'''

Finally, shading or '''''rendering''''' will complete the drawing.

=====Animation=====

<div style="clear: both;"></div>
::::::::::[[File:SlopeAnimation.gif|500px|]]

Slopes and Angles in Perspective - Revision history

DT Online: Added Template

DT Online: Added Category

DT Online: Added link

DT Online: Created article