Backsaw: Difference between revisions
From DT Online
m (Corrected Table) |
m (Corrected link capitalisations) |
||
| Line 6: | Line 6: | ||
| - the most common backsaw, typically 250mm or 300mm length with 10-14 '''[[Teeth per Inch]]''' ''(TPI)'' and used extensively for general woodworking and fine cutting of joints such as [http://en.wikipedia.org/wiki/Mortise_and_tenon '''tenons''']. | | - the most common backsaw, typically 250mm or 300mm length with 10-14 '''[[Teeth per Inch]]''' ''(TPI)'' and used extensively for general woodworking and fine cutting of joints such as [http://en.wikipedia.org/wiki/Mortise_and_tenon '''tenons''']. | ||
|- | |- | ||
| '''[[Dovetail | | '''[[Dovetail saw]]''' | ||
| - similar to a Tenon Saw but shorter at 150mm to 250mm with finer teeth at 14 to 18 TPI and used for finer work such as cutting [http://en.wikipedia.org/wiki/Dovetail_joint '''dovetail joints''']. | | - similar to a Tenon Saw but shorter at 150mm to 250mm with finer teeth at 14 to 18 TPI and used for finer work such as cutting [http://en.wikipedia.org/wiki/Dovetail_joint '''dovetail joints''']. | ||
|- | |- | ||
| '''Gent's | | '''Gent's saw''' | ||
| or '''Fancy Backsaw''' - typically 150mm long with very fine teeth ''(16 to 25 TPI)'' and used for very fine cutting of [http://en.wikipedia.org/wiki/Molding_%28decorative%29 '''mouldings'''] and [http://en.wikipedia.org/wiki/Inlay '''inlays'''] for example. | | or '''Fancy Backsaw''' - typically 150mm long with very fine teeth ''(16 to 25 TPI)'' and used for very fine cutting of [http://en.wikipedia.org/wiki/Molding_%28decorative%29 '''mouldings'''] and [http://en.wikipedia.org/wiki/Inlay '''inlays'''] for example. | ||
|- | |- | ||
| '''Razor | | '''Razor saw''' | ||
| - commonly approximately 125mm long interchangeable blades with extremely fine razor sharp teeth ''(i.e over 50 TPI)'' and used for fine work in [http://en.wikipedia.org/wiki/Ochroma_pyramidale '''balsa'''] and plastics - e.g. modelling. | | - commonly approximately 125mm long interchangeable blades with extremely fine razor sharp teeth ''(i.e over 50 TPI)'' and used for fine work in [http://en.wikipedia.org/wiki/Ochroma_pyramidale '''balsa'''] and plastics - e.g. modelling. | ||
|} | |} | ||
Revision as of 11:06, 23 October 2014
File:BackSaws.jpg
Backsaws
Backsaws have a stiffener along the top edge which helps to keep the blade straight and allows for closer control and fine work.
| Tenon saw | - the most common backsaw, typically 250mm or 300mm length with 10-14 Teeth per Inch (TPI) and used extensively for general woodworking and fine cutting of joints such as tenons. |
| Dovetail saw | - similar to a Tenon Saw but shorter at 150mm to 250mm with finer teeth at 14 to 18 TPI and used for finer work such as cutting dovetail joints. |
| Gent's saw | or Fancy Backsaw - typically 150mm long with very fine teeth (16 to 25 TPI) and used for very fine cutting of mouldings and inlays for example. |
| Razor saw | - commonly approximately 125mm long interchangeable blades with extremely fine razor sharp teeth (i.e over 50 TPI) and used for fine work in balsa and plastics - e.g. modelling. |