Backsaw: Difference between revisions
From DT Online
m (Improved presentation) |
m (Corrected link) |
||
| Line 2: | Line 2: | ||
{| cellpadding="5" | {| cellpadding="5" | ||
|- | |- | ||
| '''[[Tenon | | '''[[Tenon Saw]]''' | ||
| - the most common backsaw, typically 250mm or 300mm length with 10-14 teeth per inch ''[[Teeth per Inch|(TPI)]]'' and used extensively for general woodworking and fine cutting of joints such as [http://en.wikipedia.org/wiki/Mortise_and_tenon '''tenons''']. | | - the most common backsaw, typically 250mm or 300mm length with 10-14 teeth per inch ''[[Teeth per Inch|(TPI)]]'' and used extensively for general woodworking and fine cutting of joints such as [http://en.wikipedia.org/wiki/Mortise_and_tenon '''tenons''']. | ||
|[[File:TenonSaw.jpg|300px]] | |[[File:TenonSaw.jpg|300px]] | ||
|- | |- | ||
| '''[[Dovetail | | '''[[Dovetail Saw]]''' | ||
| - similar to a Tenon Saw but shorter at 150mm to 250mm with finer teeth at 14 to 18 ''[[Teeth per Inch|TPI]]'' and used for finer work such as cutting [http://en.wikipedia.org/wiki/Dovetail_joint '''dovetail joints''']. | | - similar to a Tenon Saw but shorter at 150mm to 250mm with finer teeth at 14 to 18 ''[[Teeth per Inch|TPI]]'' and used for finer work such as cutting [http://en.wikipedia.org/wiki/Dovetail_joint '''dovetail joints''']. | ||
|[[File:DovetailSaw.jpg|250px]] | |[[File:DovetailSaw.jpg|250px]] | ||
|- | |- | ||
| '''Gent's | | '''Gent's Saw''' | ||
| - or '''Fancy Backsaw''' - typically 150mm long with very fine teeth ''(16 to 25 [[Teeth per Inch|TPI]])'' and used for very fine cutting of [http://en.wikipedia.org/wiki/Molding_%28decorative%29 '''mouldings'''] and [http://en.wikipedia.org/wiki/Inlay '''inlays'''] for example. | | - or '''Fancy Backsaw''' - typically 150mm long with very fine teeth ''(16 to 25 [[Teeth per Inch|TPI]])'' and used for very fine cutting of [http://en.wikipedia.org/wiki/Molding_%28decorative%29 '''mouldings'''] and [http://en.wikipedia.org/wiki/Inlay '''inlays'''] for example. | ||
|[[File:FancyBackSaw.jpg|200px]] | |[[File:FancyBackSaw.jpg|200px]] | ||
|- | |- | ||
| '''Razor | | '''Razor Saw''' | ||
| - commonly approximately 125mm long interchangeable blades with extremely fine razor sharp teeth ''(i.e over 50 [[Teeth per Inch|TPI]])'' and used for fine work in [http://en.wikipedia.org/wiki/Ochroma_pyramidale '''balsa'''] and plastics - e.g. modelling. | | - commonly approximately 125mm long interchangeable blades with extremely fine razor sharp teeth ''(i.e over 50 [[Teeth per Inch|TPI]])'' and used for fine work in [http://en.wikipedia.org/wiki/Ochroma_pyramidale '''balsa'''] and plastics - e.g. modelling. | ||
|[[File:RazorSaw.jpg|200px]] | |[[File:RazorSaw.jpg|200px]] | ||
|} | |} | ||
Revision as of 12:39, 10 December 2014
Backsaws have a stiffener along the top edge which helps to keep the blade straight and allows for closer control and fine work.
| Tenon Saw | - the most common backsaw, typically 250mm or 300mm length with 10-14 teeth per inch (TPI) and used extensively for general woodworking and fine cutting of joints such as tenons. | 
|
| Dovetail Saw | - similar to a Tenon Saw but shorter at 150mm to 250mm with finer teeth at 14 to 18 TPI and used for finer work such as cutting dovetail joints. | 
|
| Gent's Saw | - or Fancy Backsaw - typically 150mm long with very fine teeth (16 to 25 TPI) and used for very fine cutting of mouldings and inlays for example. | 
|
| Razor Saw | - commonly approximately 125mm long interchangeable blades with extremely fine razor sharp teeth (i.e over 50 TPI) and used for fine work in balsa and plastics - e.g. modelling. | 
|