|
|
| Line 12: |
Line 12: |
| </span> | | </span> |
| ---- | | ---- |
| <div class="buyers-guide">
| |
| =====DT Online Buyers' Guide=====
| |
| </div>
| |
|
| |
|
| [https://en.wikipedia.org/wiki/Drill_bit#Center_and_spotting_drill_bits '''Centre Drills'''] ''(aka Slocombe Drills)'' were designed to provide a location for a '''Tailstock Centre''' ''(hence their 60deg point angle)'' but are commonly used to make a small starting indentation to guide further drilling in a '''Lathe'''.
| | {{Centre Drill Buyers Guide}} |
| * If used only to start a drilled hole then one or two of the [https://en.m.wikipedia.org/wiki/Drill_bit_sizes#Center_drill_bit_sizes mid-range sizes] will suffice since it is only the tip of the '''Centre Drill''' that will be used.
| | |
| * Choose only those made from good quality [https://en.wikipedia.org/wiki/High-speed_steel High Speed Steel] and offer them carefully up to the workpiece whilst it is rotating since the smaller sizes in particular, can break easily.
| |
| * Both larger and smaller sizes than the individual drills illustrated are available, but those shown will cover most work in '''Design and Technology'''.
| |
| * '''Model Engineers''' however, may wish to choose a set of the smaller sizes to suit to suit their more detailed precision work.
| |
|
| |
|
| {|
| |
| |-
| |
| | <dtamazon product="B00AW8372S" type="image">Dormer A200 HSS Centre Drill 3.15mm x 0.80mm</dtamazon>
| |
| | <dtamazon product="B0001OZQLS" type="image">Dormer A200 HSS Centre Drill 4.00mm X 1.60mm</dtamazon>
| |
| | <dtamazon product="B0001OZQM2" type="image">Dormer A200 HSS Centre Drill 6.30mm X 2.50mm</dtamazon>
| |
| | <dtamazon product="B0001OZQMC" type="image">Dormer A200 HSS Centre Drill 8.00mm X 3.15mm</dtamazon>
| |
| | <dtamazon product="B00AWAX8PM" type="image">Dormer A200 HSS Centre Drill 10.00mm x 4.00mm</dtamazon>
| |
| | <dtamazon product="B00T6D6RXQ" type="image">RDG Tools 12 piece set of small size centre drills</dtamazon>
| |
| |-
| |
| | <dtamazon product="B00AW8372S" type="text">Dormer A200 HSS Centre Drill 3.15mm x 0.80mm</dtamazon>
| |
| | <dtamazon product="B0001OZQLS" type="text">Dormer A200 HSS Centre Drill 4.00mm X 1.60mm</dtamazon>
| |
| | <dtamazon product="B0001OZQM2" type="text">Dormer A200 HSS Centre Drill 6.30mm X 2.50mm</dtamazon>
| |
| | <dtamazon product="B0001OZQMC" type="text">Dormer A200 HSS Centre Drill 8.00mm X 3.15mm</dtamazon>
| |
| | <dtamazon product="B00AWAX8PM" type="text">Dormer A200 HSS Centre Drill 10.00mm x 4.00mm</dtamazon>
| |
| | <dtamazon product="B00T6D6RXQ" type="text">RDG Tools 12 piece set of small size centre drills</dtamazon>
| |
| |}
| |
|
| |
|
|
| |
|
| [[Category:Drilling and Boring]] | | [[Category:Drilling and Boring]] |
Description
Also known as Slocombe Drills, Centre Drills were originally designed to create the countersink required to locate a tailstock centre when turning between centres. They have a point angle of 60° to match the angle of a Tailstock Centre
Features and Uses
A Centre Drill can also be used to provide a start location for a drill when drilling down the centre of a bar held in a Lathe chuck. Centre Drills are short and rigid enough to mark the bar centre without wandering off if they are carefully offered up to a rotating work-piece. Although their point angle does not match that a Twist Drill only a small indentation is required, so for most work in Design and Technology, this is not an issue.
Note:
Engineers may prefer a Spot Drill which is a short stubby drill designed specifically for this purpose. Alternatively, a small indentation can be cut in the bar centre with a sharp lathe tool.
Centre Drills (aka Slocombe Drills) were designed to provide a location for a Tailstock Centre (hence their 60deg point angle) but are commonly used to make a small starting indentation to guide further drilling in a Lathe.
- If used only to start a drilled hole then one or two of the mid-range sizes will suffice since it is only the tip of the Centre Drill that will be used.
- Choose only those made from good quality High Speed Steel and offer them carefully up to the workpiece whilst it is rotating since the smaller sizes in particular, can break easily.
