From DT Online
Revision as of 12:03, 2 January 2018 by DT Online
Soon after being cut down, or Felled, trees should be cut into useable sections - a process known as Conversion. A growing tree contains a high percentage of moisture and is most easily cut when in this green state. But the large amount of moisture also makes the tree heavy and so overhead cable-ways, railways and rivers are used to transport the logs to the timber yards - in addition to trucks where roads are possible.
Saws are known to have existed in Ancient Egypt from illustrations at the tomb of Nebamun and Ipuki in Thebes for example. In addition, there are many engravings and other illustrations showing the Medieval use of large two-handed Frame Saws over a Saw Pit - and the later development of powered sawmills.
Early saws were not as efficient as modern versions, and mostly powered only by hand, so it is probable that many logs were Cleaved since this is relatively easily done whilst logs are in their green state.
A Roman engineer called Vitruvious, a contemporary of Julius Caesar, refers to the lowest part of the tree which is free of knots, and after throwing away the Sapwood being, ‘‘split up into four pieces and prepared for joiner's work, and so is called 'clearstock'.’’ - [Ref: De Architectura]. This provides an early description of Timber Conversion.
A large industrial size Gang Saw can saw a whole log into planks with one pass. These are a development of the early Frame Saws with multiple blades, set a fixed width apart, that are powered to reciprocate up and down.
Gang Saws are still used and during the mid-19th Century steam powered Circular Saws were introduced leading on to the the Double Circular Saw - with one blade above the other to enable larger diameter logs to be cut.
Sawing Through and Through
As trees grow they become thicker by adding new cells beneath the bark which create a new outer ring of wood each year. These growth rings are known as the Annular Rings. The orientation of the Annular Rings, as seen on the End Grain of a board, has a significant influence on its characteristics (e.g. grain appearance, stability, wear resistance).
Live Sawing or sawing Through and Through is the most economical method of timber Conversion. With a horizontal Bandsaw successive cuts are taken down from the top down to the clamps then the log turned over to repeat.
The process produces three types of board:
- Plain Sawn (aka Slash, Flat or Crown Sawn) - the Annular Rings are at less than 450 to the face of the board;
- Quarter Sawn - the best of which is taken near the centre of the tree such that the rings are approaching 900 to the face of the board;
- Rift Sawn - a cut in between Plain Sawn and Quarter Sawn
Back Sawing, Sawing Around and Quarter Sawing are terms given other methods of conversion, some of which require the log frequently to be repositioned, but can be used to maximise the production of particular cuts of timber.
Characteristics of Different Boards
As timber dries out, the Annular Rings tend to shorten slightly and straighten out. There is little effect on the length of a board but shrinkage will occur across its width. Different cuts therefore react differently as the timber dries out.
The appearance of the Wood Gain is affected by the way the board is cut. Annular Rings at a steep angle to the face will appear as straight grain whereas if at a shallow angle, or Tangentially Cut, a wavy grain figure is produced. Also, just as with End Gain, the ends of the Annular Rings resist wear and so Quarter Sawn timber is not only the most stable but also the most hard wearing. Furthermore, Quarter Sawn timber, because it is radially cut, shows the radial Medullary Rays on the face of some timbers.
Plain Sawn, Tangentially Cut Timber
Plain Sawn timber is the most inexpensive and common type of cut. The growth rings are generally 300 or less to the face of the board. It is known as Tangentially Cut timber and is used extensively in the building industry (e.g. for joists etc.). The resulting wood displays a wavy pattern on the face of the board. Because of the curve of the growth rings this timber is most prone to Cupping.
Quarter Sawn, Radially Cut Timber
Radially Cut timber produces the most stable and hard wearing timber but it is also the most expensive. Annual growth rings form an angle greater than 450 to the face of the board. Live Sawing produces only a limited amount of Quarter Sawn boards and Quarter Sawing can involve the log being repositioned many times to produce the radial cuts, which increases cost. It also results in more waste. Quarter Sawing may be used for timbers such a Oak for example, because cutting along its Medullary Rays will produce the much prized highly figured Oak.
Rift Sawn Timber
Rift Sawn (shown shaded) is the cut which falls between Plain Sawn and true Quarter Sawn. Annual growth rings form an angle between 300 and 600 to the face of the board making it suitable for quality floor boards, for example, because it wears well and is reasonably stable. It is straight grained but, because it is not Radially Cut does not reveal any 'silver ribbon' grain features in timbers such as Oak.